Join Free or Sign in
Shopping Cart 0
$0.00

PicoBoo AC

SKU
FI-105
In stock
  • 1 x Trigger Input
  • 2 x 110v AC Outputs
  • Up to 2 Minutes of Animation
  • Up to 2 Minutes of 8-bit Mono Audio
  • 10 Watt Internal Amplifier
  • Power Cable Included
$109.99
The PicoBoo AC is also available in a Starter Kit.





The PicoBoo AC is an ideal controller for AC devices and requires no wiring.







Simple, Intuitive Programming


All of the programming for our PicoBoo AC controllers is done in real-time using the buttons on the front of the device. This allows you to create complicated patterns and match them up with sounds with just the push of a few buttons. You can test your program immediately after creating it.





Supports Audio


Using a built-in flash memory chip, you can playback audio and even record up to two minutes of your own sounds to work with your animation. Plug in any audio device in the audio input and watch the sound go right on the chip. No need to drag out your laptop, update all your drivers, or deal with frustrating sound format conversion. You can also record up to eight sounds which the PicoBoo AC will automatically rotate through.





Included Amplifier


The PicoBoo AC comes with 10 watt internal Class D amplifier - you can use standard speakers which are easier to hide right in your props.







AC Outputs


The PicoBoo AC has two 10 amp relays brought out to two standard AC outlets. If you want to leave a light on and deactivate it when the scene begins, you can easily set each of the outputs to either a "normally on" or "normally off" position. As the PicoBoo AC is fused at 10 amps, the total current consumed by both outlets together has to remain below 10 amps.



Up to 2 minutes of animation at 30 frames per second can be recorded.







Activate Using Triggers


PicoBoo AC prop controllers have a trigger input that can be used to automatically activate your scare program. You can use this input with infrared motion sensors, beam sensors, pressure sensing mats, hand triggers, or a number of other triggers. You can also set the device to just loop the program over and over again by connecting the - and the IN trigger pins with a small wire.

Our selection of triggers can be seen here.







Ambient and Scare Modes


The PicoBoo AC controller, by nature, stays in an ambient mode. You can set up a scary background noise or even ominous music for your guests to hear by programming it on to the sound chip. In ambient mode, you can only program audio.







Write-Protection


The PicoBoo AC, like all our Halloween prop controllers, has a write-protection mechanism so you don't accidentally lose or change your program.



Write Your Own Review
You're reviewing:PicoBoo AC
Your Rating
Customer Questions
Is there a way to loop the program?

Yes, you simply put a piece of wire into the trigger input.

Can I have the recorded program run and repeat indefinitely without needing to be triggered each time?

Yes.

Would there be any problems if I wired one trigger to activate two PicoBoo controllers at the same time?

That can be done by following the instructions in this document.

Can I plug powerstrips into the PicoBoo AC, that way AC several lights / props are triggered simultaneously?

Yes, as long as the total of connected devices to not exceed 10amps.

Can I record audio into the controllers via my Android or iPhone?

Yes.

Can a reed switch be used as a trigger?

Yes. Most reed switches are normally-closed, so depending on your application you might have to set the trigger mode on the PicoBoo to normally-closed too. Either way it will work.

How do I make it continuously play without having to trigger it?

Simply put a jumper (piece of wire) into the trigger input terminals and it will play the program continuously.

Is there a way to delay the sound starting, say for a few seconds, once the trigger is activated?

The way to do this is to record some silence into the beginning of your audio file.

After the PicoBoo is triggered and running animation, will another trigger during the animation restart the animation?

No, the program will run to completion.

How can I add delay time on my PicoBoo?

Simply record nothing: For a pre-delay press REC then wait as long as you want the pre-delay to be then press the 1 & 2 buttons for your animation then press REC to save. For a post delay do the same thing but wait at the end before pressing REC to save.

Will this controller run servos?

This controller does not support servos. The products that do are the BooBox Flex MAX and the PicoTalk.

Is it possible to trigger this controller with a wireless remote from Home Depot?

NO! Motions sensors from the hardware store are 120V AC and will burn up the controller. Only 12VDC trigger devices must be used with the controllers.

How long can I record/play ambient sound? Is it only two minutes looped over and over?

Two minutes maximum ambient + scare sound combined.

Scare sound only plays for 2 seconds

The scare sound will only play as long as the animation. Record longer animation.

Can the motion sensor trigger be 5VDC or must it be 12VDC?

Short answer: Not easily. Long answer: The controller provides 12VDC to power triggers. It will not supply 5VDC. If you need to use 5VDC you can power your motion sensor with your own 5VDC power supply or follow the instructions here to step the 12VDC voltage down to 5VDC.

Video 1

Video 2

Video 3

For assistance with this product visit the Support & Training Center or Contact Us